DRL152K Marina based roadster rebuild

[listerjp2]

Keep it coming, I'm really enjoying this thread.

Adrian

[martinclan56]

I thought it was about time to do a reality check and make sure the gearbox actually fitted in my new transmission tunnel. I had to take the hacksaw to one of the unused lugs on the gearbox casing but now it fits with about 1/2" clearance on either side which hope is enough for any movement. And the propshaft fits as well, always a bonus....
gearbox_fit1 by Robin Martin, on Flickr
propshaft_check1 by Robin Martin, on Flickr
From the front it looks like I may have to adjust the position of the fuel line but I'll wait untill the gearbox is finally fitted before I do that.
gearbox_fit2 by Robin Martin, on Flickr
And I have taken the advice of various sages and fixed the tunnel top using M5 screws and rivet nuts. I have put the ignition switch on the top of the tunnel, the idea being all of the wiring is then almost impossible to get at for any would be joy rider. The switch itself is an industrial tamper proof item. NOS from ebay for a bargain tenner.
transmission_tunnel by Robin Martin, on Flickr
And yes the gearbox is almost new! It looks like it had been recently fitted before I bought the car from the previous owner and builder.

[wiggiesworld]

Makes sense now.... Can't beat a good 2CV, have owned a couple over the years. Cornering is a riot and a case of trusting the car to not do a Reliant Regal on you!

[martinclan56]

I probably didn't explain it well!
There wasn't really an oil seal in the conventional sense. The splined joint is greased. The original arrangement was just a primitive cork washer the job of which was to keep the grit out and the grease in. I think the gaiter should do the same job. It works well on millions of 2CV's!

[wiggiesworld]

Very useful that these fit but surely this doesn't resolve your issue of holding the oil seal in place? Regardless of putting on a gaiter I would expect you would still need a correctly fitting oil seal.

[martinclan56]

I have been pondering the problem of my propshaft for some time now. For some reason the little screwed cap that holds the oil seal on the splined joint is way to big and hence impossible to screw up. I can only think that it has come loose at some point and years of rattling arround on the propshaft joint has stretched it. Its at least 3mm too big in diameter.
propshaft_problem by Robin Martin, on Flickr
Anyway I was doing some routine maintenance on the Pembleton. The driveshafts (2cv) have 3 joints the centre one of which is a sliding spline like on a propshaft. They are all protected by rubber gaitors. So I got out the callipers and, would you believe it, the size of the shafts making up the splined joint is almost the same as that on the Marlin propshaft. Getting excited now... So I ordered a gaitor from ECAS, the main source for 2CV spares and it fits perfectly!
propshaft_solution by Robin Martin, on Flickr
Not very often you get a piece of luck like that.

[phild]

I have been looking at this post and your progress for a long time and have picked up lots of ideas from your posts which I will incorporate in my newly restarted build as I will need to get my Marlin though IVA cheers Phil

[martinclan56]

I think it looks brilliant, I wish I had thought of doing that when I did mine.

Adrian

Thank-you - but I have to confess it wasn't 100% my idea. As with many things it is just a refinement of what somebody else already did.

Cheers, Robin

[listerjp2]

I think it looks brilliant, I wish I had thought of doing that when I did mine.

Adrian

[martinclan56]

As suggested I have made everything line up with the scuttle top. I am still not convinced though ;-)
dashboard3 by Robin Martin, on Flickr
The little rectangle of masking tape immediately in front of the steering wheel represents the tiny digital (bicycle) speedo I am using. Not very "classic" but practical and cheap! And removable.
I have been trying not to buy any parts with the classic car label as it seems to add a premium to the cost. But the Lucas trafficator switch you can see is perfect for the job. I can operate it without removing my hands from the steering wheel as per the IVA rules and - well - it looks the part. I don't need an IVA as the car is already registered, but I consider the rules to be a good guidline where practical.

[andyf]

Yes, seems like the right choice

[martinclan56]

Looks like it's sloping then

[listerjp2]

I vote for sloping also.

Adrian

[MOC Chair]

I also vote for sloping

[dcunn]

1 vote for sloping